Curious about Actual Cisco CCNP (300-510) Exam Questions?

Here are sample Cisco Implementing Cisco Service Provider Advanced Routing Solutions (300-510) Exam questions from real exam. You can get more Cisco CCNP (300-510) Exam premium practice questions at TestInsights.

Page: 1 /
Total 214 questions

Want more questions? Get Premium Access.

Question 1

What is the difference between RPL and route-maps?

AUnlike RPL. route-maps are supported with IPv4 address families only

BUnlike route-maps, only RPL supports extcommunity sets to group extended communities.

CUnlike RPL. route-maps are designed for BGP protocol only.

DUnlike route-maps, only RPL is designed for bulk configuration of multiple devices.

Correct : B

Options Selected by Other Users:

Mark Question:

Start a Discussions

Submit Your Answer:

AUnlike RPL. route-maps are supported with IPv4 address families only

BUnlike route-maps, only RPL supports extcommunity sets to group extended communities.

CUnlike RPL. route-maps are designed for BGP protocol only.

DUnlike route-maps, only RPL is designed for bulk configuration of multiple devices.

0 / 1500

Question 2

Refer to the exhibit.

300-510 Exam Question 2 Exhibit 1

Refer to the exhibit. An engineer is troubleshooting a network routing issue on this IS-IS network situated at the customer's regional hub. Router 2 that runs Cisco IOS XR Software cannot see the network 10.1.1.0/24 on router 1. The Layer 2 encapsulations are correct. The ARP connectivity for the Ethernet interface that runs IS-IS is working. Which action resolves the issue?

AOn router 1, remove the CISCOLIVE keyword after the Ip router Isis command under interface GigabitEthernet0/2.

BUnder the router isis command on router 1. change is-type level-1 to is-type level-2

COn router 1. add the CISCOLIVE keyword after the Ip router isis command under interface GigabitEthernet0/3.

DUnder the router isis command on router 2. change is-type level-1 to is-type level-2

Correct : C

Options Selected by Other Users:

Mark Question:

Start a Discussions

Submit Your Answer:

AOn router 1, remove the CISCOLIVE keyword after the Ip router Isis command under interface GigabitEthernet0/2.

BUnder the router isis command on router 1. change is-type level-1 to is-type level-2

COn router 1. add the CISCOLIVE keyword after the Ip router isis command under interface GigabitEthernet0/3.

DUnder the router isis command on router 2. change is-type level-1 to is-type level-2

0 / 1500

Question 3

What is the function of BGP confederations?

AThey require routers to use private AS numbers.

BThey eliminate the need for a fully-meshed internal BGP design.

CThey enable a single device to distribute a common configuration to its peers

DThey assign an external BGP router to serve as the route reflector

Correct : B

Options Selected by Other Users:

Mark Question:

Start a Discussions

Submit Your Answer:

AThey require routers to use private AS numbers.

BThey eliminate the need for a fully-meshed internal BGP design.

CThey enable a single device to distribute a common configuration to its peers

DThey assign an external BGP router to serve as the route reflector

0 / 1500

Question 4

Refer to the exhibit.

300-510 Exam Question 4 Exhibit 1

Refer to the exhibit. The Cisco router has a single uplink to the upstream network, which is critical to the business. The router is configured for traffic steering with the Autoroute mechanism configured to steer all OSPF and IS-IS prefixes over non-shortest paths and divert traffic for those prefixes to the SR-TE policy. However, the Autoroute Announce functionality for all prefixes is not working. Which additional command set must the engineer configure on the router to correct this issue?

300-510 Exam Question 4 Exhibit 2

AOption A

BOption B

COption C

DOption D

Correct : D

Options Selected by Other Users:

Mark Question:

Start a Discussions

Submit Your Answer:

AOption A

BOption B

COption C

DOption D

0 / 1500

Question 5

Refer to the exhibit.

300-510 Exam Question 5 Exhibit 1

IS-IS is the routing protocol on the network. After the team noticed excessive CPU usage on all routers, particularly routers R2 and R6, they configured route summarization on all routers. However, a network engineer noticed that summary routes and more specific routes are present in the routing table on R1. Which action must the team take so that R1 receives only the summary routes?

AConfigure R2 and R4 to perform summarization for Level 1 routers.

BConfigure R3 to perform summarization for Level 1 routers, and configure R6 to perform summarization for Level 2 routers.

CConfigure R3 and R5 to perform summarization for Level 1 and Level 2 routers.

DConfigure R6 only to perform summarization for all routers.

Correct : B

Options Selected by Other Users:

Mark Question:

Start a Discussions

Submit Your Answer:

AConfigure R2 and R4 to perform summarization for Level 1 routers.

BConfigure R3 to perform summarization for Level 1 routers, and configure R6 to perform summarization for Level 2 routers.

CConfigure R3 and R5 to perform summarization for Level 1 and Level 2 routers.

DConfigure R6 only to perform summarization for all routers.

0 / 1500

Page: 1 / 43
Total 214 questions

Unlock Full
300-510 Exam Features

In Just $49 You can Access

All Official Question Types
Interactive Web-Based Practice Test Software
No Installation or 3rd Party Software Required
Customize your practice sessions (Free Demo)
24/7 Customer Support

Get Full Access Now

Marked Questions
300-510 Exam

300-510 Exam Question 1
300-510 Exam Question 2
300-510 Exam Question 3
300-510 Exam Question 4
300-510 Exam Question 5

Download PDF File Demo

Try Web-Based Exam Practice Software Demo

Commenting

In order to participate in the comments you need to be logged-in.
You can sign-up or login